Teco Tube Expanders Company

Note: puncture the tube to ensure that pressure cannot build up in the tube and cause the plugs to loosen or blowout. Suitable for cutting steel and non-ferrous tubes in con- densers, heat exchangers and boilers. Adjustable for tube sheet thickness from 2” to 6” (50.8 mm to 152.4 mm). Available for tubes from 1/2” to 2 1/2” (12.7 to 63.3 mm) O.D.. The TECO one revolution tube cutter is designed for hand operation using a ratchet or hand wrench of proper size to fit the drive shank of the tool. The cutter bit operates TUBE REMOVAL TOOLS Tube O.D. 10 Gauge 11 Gauge 12 Gauge 13 Gauge 14 Gauge 15 Gauge 16 and 17 Gauge 18 and 19 Gauge Cutter Bit 1/2” (12.70 mm) TCOR- 500-18 CB- 625-7-12N 5/8” (15.88 mm) TCOR- 625-10 TCOR- 625-11 TCOR- 625-12 CB- 625-7-12N 5/8” (15.88 mm) TCOR- 625-13 TCOR- 625-14 TCOR- 625-15 CB- 625-13-15N 5/8” (15.88 mm) TCOR- 625-16 TCOR- 625-18 CB- 750-7-11N 3/4” (19.05 mm) TCOR- 750-10 TCOR- 750-11 CB- 750-7-11N 3/4” (19.05 mm) TCOR- 750-12 TCOR- 750-13 TCOR- 750-14 TCOR- 750-15 TCOR- 750-16 TCOR- 750-18 CB- 750-12-19N 7/8” (22.22 mm) TCOR- 875-10 TCOR- 875-11 TCOR- 875-12 TCOR- 875-13 TCOR- 875-14 TCOR- 875-15 TCOR- 875-16 TCOR- 875-18 CB-1000-7-11N 1” (25.40 mm) TCOR-1000-10 TCOR-1000-11 CB-1000-7-11N 1” (25.40 mm) TCOR-1000-12 TCOR-1000-13 TCOR-1000-14 TCOR-1000-15 TCOR-1000-16 TCOR-1000-18 CB-1000-12-19N 1 1/4” (31.75 mm) TCOR-1250-10 TCOR-1250-11 TCOR-1250-12 TCOR-1250-13 TCOR-1250-14 TCOR-1250-15 TCOR-1250-16 TCOR-1250-18 CB-1000-12-19N 1 1/2” (38.10 mm) TCOR-1500-10 TCOR-1500-11 TCOR-1500-12 TCOR-1500-13 TCOR-1500-14 TCOR-1500-15 TCOR-1500-16 TCOR-1500-18 CB-1500-10-19N 1 3/4” (44.45 mm) TCOR-1750-10 TCOR-1750-11 TCOR-1750-12 TCOR-1750-13 TCOR-1750-14 TCOR-1750-15 TCOR-1750-16 TCOR-1750-18 CB-1500-10-19N 2” (50.80 mm) TCOR-2000-10 TCOR-2000-11 TCOR-2000-12 TCOR-2000-13 TCOR-2000-14 TCOR-2000-15 TCOR-2000-16 TCOR-2000-18 CB-1500-10-19N 2 1/4” (57.15 mm) TCOR-2250-10 TCOR-2250-11 TCOR-2250-12 TCOR-2250-13 TCOR-2250-14 TCOR-2250-15 TCOR-2250-16 TCOR-2250-18 CB-2250-10-19N 2 1/2” (63.50 mm) TCOR-2500-10 TCOR-2500-11 TCOR-2500-12 TCOR-2500-13 TCOR-2500-14 TCOR-2500-15 TCOR-2500-16 TCOR-2500-18 CB-2250-10-19N on an eccentric principle. With the cutter bit in the closed position insert the cutter into the tube to be cut. Apply wrench and turn in a clockwise direction. The tool bit will move out and pierce the tube wall. Continued turning and cut the tube off in one revolution. The cutter is then turned counterclockwise slightly to close in the bit allo- wing the cutter to be removed from the tube. The TECO one revolution tube cutter can also be used to puncture the tube before plugging. This ensures that pressure cannot build up in the tube and cause the plug to become loose or blow out. ONE REVOLUTION TUBE CUTTER NEWMODEL For sealing off leaky condenser and heat exchanger tubes without damaging tube sheets. Tapered pin is driven into ring, which is tapered on the inside and is parallel to tube on the outside. This gives even expansion to the ring and a long contact to the seal. Available in a variety of metals. Specify Tube O.D. and Gauge. Ideal for sealing leaky tubes in condensers or heat exchangers. Just drive a plug into each end of leaky tube. Available in a variety of metals. Specify Tube O.D. and Gauge. TWO PIECE TUBE PLUGS TAPERED TUBE PLUGS Other sizes and/or special reaches on request. tube expanders company 40